12 Best Range Hoods for Gas Stoves (October 2026)

A gas range throws off more than heat and steam. An open blue flame sends combustion byproducts into the room, and the fine grease aerosol that comes off a hot burner is exactly the kind of particulate a range hood was built to catch. That is why picking the best range hoods for gas stoves comes down to airflow first and everything else second.

Most people pick backwards. They fall for the lighting package or the touch panel and then discover the motor moves 200 cubic feet per minute, which is not enough to hold the plume down over a wide-open burner. Our team compared airflow ratings, published noise figures, filter types and mounting formats across 12 models to find the ones that actually control a gas cooktop.

Here is the short version. For a typical 30-inch gas range with a combined burner output in the 40000 to 60000 BTU range, most households need a ducted hood rated between 400 and 600 CFM. Push past 600 CFM for wok cooking, cast iron searing or a 48-inch range, and read the makeup air section before you buy anything.

If your hood goes under existing cabinetry, our guide to the best under-cabinet range hoods covers the clearance math in more depth. If the cooktop sits on an island in an open plan, start with island range hoods for open kitchens instead, because capture geometry changes completely when there is no wall behind the burner.

Top 3 Picks for Gas Stove Cooking in 2026

Best Range Hoods for Gas Stoves in 2026: Quick Comparison

1. Broan-NuTone 413023 Ductless 30-Inch Insert – Editor’s Choice

This is the insert most people end up with and most people keep for years. It drops into a 30 inch cabinet cutout, wires to a standard box and starts pulling air through a replaceable charcoal filter. Owners consistently describe the install as a ten-minute job, which matters more than any spec on the box.

We picked it as the editor’s choice because the numbers behind it are hard to argue with. It carries a 4.6 average across more than twenty thousand ratings, which is a larger sample than anything else in this roundup by an order of magnitude.

The two-speed fan is genuinely quiet relative to the air it moves, and the rocker switches are the kind of hardware that still works after a decade of greasy fingers. The wide selection of sizes and finishes also means it fits into an existing cabinet run without a custom part.

Be clear about what you are buying, though. This unit recirculates rather than exhausts, so it filters and re-releases air instead of sending combustion byproducts outside. In a ventless apartment or a cabin, that is a reasonable compromise, and for gas cooking it is a real limitation worth weighing.

Who the Broan-NuTone 413023 suits

This is the right call for a 30-inch gas range in a kitchen where the stove already has an over-range microwave that is due for replacement. The 1.3 pound body is light enough for one person, the footprint is a standard 30 inches, and the charcoal filter is a consumable you can swap in a minute.

It also suits anyone who wants a hood that will not be the reason a remodel goes wrong. Nothing here is exotic, and the parts are all standard.

Who should skip it

Skip it if you sear on cast iron twice a week or wok cook regularly. Reviewers consistently describe the fan power as modest, and recirculation mode simply cannot compete with a ducted unit for a heavy plume.

Also expect a dim light. The unit takes a standard LED bulb, but the diffuser guard is a separate purchase, and several owners mention a small gap where the housing is not perfectly square against certain cabinets.

2. Hauslane PS18 30-Inch Under Cabinet – 860 CFM of Under-Cabinet Power

This is the most capable under-cabinet hood in the group, and for a gas range that matters more than the slim profile. The 860 CFM figure is the highest airflow we saw on a unit that still fits inside a standard 30 inch cabinet opening.

Six speed settings let you run it near-silent while simmering and then open it up when the pan hits a hard sear. Owners report the suction is strongest at the rear of the cooktop, so center your burners when you can.

The build is thick stainless rather than the tinny stamped steel common at this size, and the baffle filters carry a see-through grease tray window so you can see when they need washing. All three duct adapters ship in the box, which removes the most common reason a weekend install turns into a hardware-store run.

There is one caveat on airflow. Power Control Technology caps the output below 350 CFM in some configurations, so check the manual for the setting you plan to use with a gas range before you commit.

What works about the Hauslane PS18

For a high-output gas range, this is the hood we would put in. The combination of 860 CFM, six speeds and a genuine baffle filter array handles the wok burner and the big sear without any of the guesswork that comes with an undersized unit.

The lifetime motor warranty is unusual at this level of build quality, and reviewers note that customer service has replaced defective models rather than arguing with owners.

Where it frustrates people

Installation is the friction point. The rear mounting screw holes sit recessed behind the fan housing, the manual has no drilling template, and at 41 pounds most owners describe it as a two-person job or one that needs a cabinet jack.

Noise is a fair concern too. The published figure is 7 sones, and several owners find it louder than they expected at mid and high speeds even after the low settings prove genuinely quiet.

3. IKTCH 30-Inch Wall Mount 900 CFM – Best for High-Heat Searing

A wall-mounted chimney hood is the format most gas ranges were designed around, and this one brings 900 CFM to it. That is tied for the highest airflow in our test group, which means it can hold a plume down over a burner running wide open.

The four speed settings are spread across 40 to 65 decibels, so you can run the low setting during a long braise and still have real headroom when the pan is smoking. Gesture sensing and touch controls both work, and reviewers like being able to start the fan without touching anything.

Both filters are permanent stainless units that go in the dishwasher, so there is no consumable cost over the life of the hood. The two lamps have adjustable brightness, which is a small thing that makes a big difference at midnight, and the unit is ETL listed.

The five-year manufacturer warranty is longer than most of the wall mounts we looked at. A remote control is included for when the chimney is out of reach from the cooktop.

Where this hood earns its badge

Choose it when your gas range has a high combined BTU rating, when you cook with a wok ring, or when the cooktop sits against a wall with an exterior vent route already planned. The 900 CFM figure leaves real margin above the 400 to 600 CFM band most gas ranges need.

It also suits anyone who wants permanent filters. No replacement purchases, no charcoal cartridges, and the dishwasher handles the grease.

Where it does not fit

It needs vertical space. The unit stands just over 51 inches tall, so a low ceiling or a soffit over the range rules it out, as does any kitchen without a path to the outside.

At 45 pounds, plan on a second person for the install. This is not a one-person lift.

4. IKTCH 36-Inch Built-In Insert 900 CFM – Best Built-In Design

This is the only true built-in insert in the group, and it is the one we would specify for a kitchen with custom cabinetry. The 900 CFM output is unusual for a unit that disappears flush into a cabinet, and the sightline to your range stays completely open.

It carries the highest average rating in the group at 4.5, and the review pattern is consistent: airflow and installation satisfaction are high, weight and cutout accuracy are the recurring gripes.

Three dishwasher-safe stainless baffle filters come standard, and each one has a pull handlebar so you can slide it out without getting grease on your fingers. Four speeds span the same 40 to 65 decibel range as the wall-mount model, with remote and gesture control and adjustable LED brightness on two lamps.

The unit is ETL and CETL compliant, which is worth noting if your inspector is the kind who asks. Sizes cover 30, 36 and 42 inch openings, so it scales with a larger range.

Why buyers choose the built-in format

A built-in insert gives you the airflow of a full chimney hood with none of the visual bulk. If your cabinets are already custom, the hood reads as part of the millwork rather than an appliance hung off the wall, and a 36 inch opening matches a 36 inch range without gaps.

It suits a remodel where the cabinet boxes are already in place and you are swapping a microwave for a proper hood.

What to watch out for

Measure the cabinet cutout twice and compare it against the 18.5 by 34.38 inch body dimensions. Owners who rush the measurement end up with a unit that does not sit square in the frame.

At 44.8 pounds this is the heaviest insert we tested, so budget for a helper. It also sits at the premium end of the category, which is a lot of money to spend if your gas range is a modest 30 inch model.

5. AMZCHEF 30-Inch 750 CFM – Best Feature Set Under a Cabinet

The AMZCHEF does the most with the space it takes up. It delivers 700 to 750 CFM from a body that measures 29.8 by 19.7 by 5.98 inches, which puts it in territory usually reserved for wall-mount chimneys.

Three control paths is unusual at this level. You have a touch panel, a gesture sensor and a remote, so you can start the fan mid-cook without crossing the kitchen or touching a greasy panel.

The two stainless baffle filters are dishwasher-safe and described by owners as resistant to grease, stains and rust. Both round and rectangular duct outlets are supported, and the 6 inch air outlet matches standard duct sizing for a hood of this output.

Install weight is a genuine plus. Owners fitting this over a gas range alone report finishing in about an hour, even as a first-time DIYer.

Best for feature-focused buyers

This suits anyone who wants real high-heat airflow without the chimney, and who values remote and hands-free control. It also works well over a 30 inch gas cooktop in a kitchen where cabinet clearance is generous but ceiling height is not.

The timer function on the LCD screen is useful for gas cooking in particular, since it lets the fan keep running after you step away from a burner you left on low.

Where the features get in the way

The LCD panel is very bright and has no dimming option, which several owners find unpleasant in a dark kitchen. The gesture sensor also fires when you reach into the cabinet above, which happens constantly over a cooktop.

Expect noise on the top setting, a remote with roughly two meters of range and no storage, and no drilling template in the box. The included screws are short, so plan to pick up longer screws with washers if you are mounting into solid cabinet material.

6. COSMO Vista 36-Inch 380 CFM Wall Mount – Best for Wider Ranges

The Vista is a 36 inch wall-mount hood, which makes it the natural match for a 36 inch gas range. The extra width matters for capture, because a hood that matches the cooktop width catches more of the rising plume than a narrow 30 inch unit.

The published noise figure is 45 decibels on the lowest speed with rigid ducting, and reviewers describe it as among the quietest operations they have owned. That matters in an open kitchen where the hood runs during conversation.

ARC-FLOW permanent filters go straight into a dishwasher, so there is no filter replacement cost over the life of the unit. The two watt LEDs are described as long-lasting with high lumen output, which solves the dim-light problem that plagues several cheaper models in this group.

The box includes a 3-prong plug, a damper, an exhaust vent and the fan hardware, so a weekend install does not require a separate hardware run.

Why this one fits a 36-inch range

If you have a 36 inch gas range, a 36 inch hood is the correct starting point for capture geometry. The adjustable chimney spans roughly 25.6 to 39.4 inches, which covers a wide range of standard ceilings.

It suits buyers who cook at a moderate pace rather than running a wok burner constantly, and who would rather have a permanently quiet kitchen than maximum raw airflow.

The limits you should know about

380 CFM sits in the middle of the range we tested. It handles simmer, sauté and a normal sear on a 30 to 36 inch gas range, but it is not the hood to reach for heavy high-heat work or a large wok ring.

It is also ducted only as standard. Running it ductless requires the separate CFK1-TM carbon filter kit, and the three-speed control is fewer settings than the six-speed and four-speed models we reviewed.

7. Tieasy 30-Inch 450 CFM Chimney Hood – Best Value Wall Mount

450 CFM is the number most gas ranges actually need, and the Tieasy delivers it in a full chimney format. That combination makes it the value pick among the wall-mount options in this group.

The 55 decibel rating sits mid-pack, but owners describe the running noise as negligible for the air delivered. That is the metric that matters, since a quieter-sounding rating with half the airflow helps you less.

Five-layer reusable aluminum mesh filters mean no consumables at all. The adjustable chimney cover hides the ducting and gives the kitchen a finished focal point, and it adjusts from about 15.75 to 29.5 inches to suit ceilings between 7.5 and 8.5 feet.

Hardware, duct pipe, backdraft damper and flue covers are all in the box, and the 5-year parts warranty is longer than most competitors offer. Reviewers also report it still looks and performs well after two years.

Where it makes sense

This is the pick for a standard 30 inch gas range in a room with normal ceiling height and a vent route. It also shows up often in rental flips, because repeat buyers like the combination of output, warranty and a finish that photographs well.

Pick it when you want a real chimney hood silhouette without stepping up into the high-CFM premium tier.

What could go wrong

The manual is metric-only and thinly described, so US installers have to convert dimensions on the fly. The protective blue plastic film on the baffle filters is notoriously hard to peel off, and the surface scratches easily while you position the unit.

One long-term owner reported a strong odor and no grease collection container in ductless mode, and the carbon filter kit for that setup is a separate purchase.

8. COSMO Delta 30-Inch Slim Under Cabinet – Best for Small Kitchens

The Delta solves a specific problem: a kitchen where the cabinet above the range is shallow and a full-depth hood would block your view. At 5.5 inches tall, it is one of the slimmest units we tested and still moves a workable amount of air.

The multi-layer aluminum mesh filters are reusable and dishwasher-friendly, so the ongoing cost is the same as a permanent baffle filter. Three fan speeds give you more control than the two-speed budget models.

It is convertible, so it can run ducted to an exterior vent or ductless with an optional carbon filter kit. The listed noise is 50 decibels on the lowest speed with rigid ducting, which is a good figure for a unit this thin.

Owners like the stainless finish, describing it as commercial-looking and well gauged for the size, and several detailed reviews walk through under-cabinet mounting pitfalls the stock instructions skip.

Who should pick the Delta

Choose it for a condo, an apartment or a galley kitchen where cabinet clearance is tight and you still want a real hood instead of an over-range microwave fan. It also works for a gas cooktop in a kitchen where you sauté and boil more than you sear.

The convertible venting is useful if you might add an exterior vent later but are not ready to run ductwork now.

Who should look elsewhere

Do not buy it for high-heat work. Owners describe the suction as adequate rather than powerful, which is fine for a gas range used for daily cooking and short of what a wok burner or a heavy sear demands.

The lighting is the most repeated complaint, with a small 1 by 3 inch lens mounted at the rear that several owners call close to useless. The included screws are also soft enough that many people substitute bolts.

9. FIREGAS 30-Inch White 300 CFM – Best Budget Airflow

The FIREGAS is the useful middle of the budget tier. At 300 CFM it out-moves every other entry-level under-cabinet hood we tested, which makes it a real step up from an over-range microwave fan in the same price bracket.

Owners report it running noticeably quieter than the microwave fan it replaced, and the 2-speed rocker control is about as simple as controls get. The 4.7 inch body clears low-hanging cabinets that rule out deeper models.

The steel construction and electricals are described as holding up over years of daily use, and rolled edges avoid the sharp corners that make slim hoods awkward to handle during fitting. It is convertible between ducted and ductless, which keeps it usable in homes without a vent path.

The white finish is a genuine differentiator. Most of the slim models in this group are stainless, so this is one of the few options that suits a traditional or shaker kitchen.

When the FIREGAS makes sense

It suits a first-time buyer replacing a dead microwave fan over a 30 inch gas range, and it suits a rental or a starter kitchen where you want more airflow per dollar than the other options offer. The 2,062 ratings suggest it is a well-trodden path.

It is also a good fit if cabinet clearance is genuinely tight, since the body is only 4.7 inches tall.

What to plan around

The wiring is not enclosed in an electrical box, and more than one reviewer has retrofitted a cover themselves. Add a junction box to your install list.

The 7 inch duct outlet is oversized for 300 CFM, so you will need an adapter for a standard duct run. The 2 watt LED is dim, the lamp holder is not user-replaceable, and at least one review reports an inaccurate drilling template.

10. Zomagas 30-Inch 280 CFM Slim Hood – Best for First-Time Buyers

The Zomagas pairs a 4.5 rating with an airflow figure that beats most of the sub-entry tier. At 280 CFM in a body just 4.7 inches tall, it delivers more air per inch of cabinet space than anything else we tested at this level.

Two-way venting means you can run the 7 inch top duct or use the rectangular rear vent, and the carbon composite filter covers the ductless option. That flexibility makes it a safe choice in older homes.

The rocker switches have no menu to navigate, which is exactly what a first-time buyer wants. Reviewers also like the 17.5 inch depth, which clears low-hanging cabinets that would not take a 19 inch body.

It ranks high in the category, which is a decent proxy for how many people have fitted one and lived with it. At 55 decibels it stays conversational.

Why first-timers like it

There is nothing to learn. Two speeds, two rocker switches, one LED, and a mounting pattern that fits a standard 30 inch cabinet opening. It suits a first apartment or a first kitchen where you want a genuine hood without a steep learning curve.

For a gas range used for everyday cooking rather than constant high heat, 280 CFM with a top vent is a workable combination.

Where it falls short

No junction box is included, and the manufacturer recommends buying one separately to enclose the wire connections. Plan for that before the install starts.

The three-layer filter combines aluminum mesh with an activated carbon composite that is a consumable, needing replacement every three to four months. Two fan speeds give you less control than a three-speed model when you are trying to balance noise against output.

11. SNDOAS 30-Inch 230 CFM Slim Hood – Best for Rental Units

The SNDOAS is the one we would buy in bulk for rental flips. It has the second-highest rating in the group at 4.5, it ranks near the top of the category, and owners fitting out rental properties describe the install as fast and straightforward.

At 4.7 inches tall it clears cabinet slots that defeat deeper units, and the 430 grade brushed stainless with a rolled profile wipes down easily. Aesthetically it reads far better than the plain boxy budget units.

It ships with a drilling layout sheet showing screw placement, which is a small thing that separates it from most competitors in this price band. The 56 decibel rating is respectable for 230 CFM.

The carbon filter for ductless operation is included rather than sold separately, which helps when you are outfitting several identical units and want to keep the parts count low.

Where it works well

This suits a landlord outfitting a rental, or a renter who cannot alter the ductwork and needs a slim unit that still removes grease and odor. It also works for a gas cooktop in a smaller kitchen used for daily cooking rather than high-heat searing.

The two-way venting lets you choose top or rear exhaust depending on where the wall or cabinet allows.

What to account for

There is no cover plate over the electrical connections, leaving them exposed to grease and steam. Add a junction box when you install it.

The LED has one brightness setting and is not bright, and the module may not be replaceable without replacing the whole hood. The exhaust pipe for top venting is not included either, so add that to the parts list.

12. COMFEE 30-Inch 200 CFM Hood – Best for Light Daily Cooking

The COMFEE is the quietest-running model in the group on its published figure, and its hand-motion control is the feature owners mention most. Wave at the panel and the fan starts, which solves the problem of greasy hands on a touchpad better than almost anything else here.

It also uses a standard replaceable A19 bulb through an E26 holder, so you choose the brightness yourself. That single detail fixes the dim-light complaint that shows up on half the models in this roundup.

Two washable filters are included, one aluminum mesh and one aluminum and activated carbon composite, so both ducted and ductless setups are covered out of the box. The 5.6 inch body sits flush against the cabinet base and is a good fit for a condo.

At 11 pounds it is one of the easiest to handle, and at least one owner reports it running more quietly than the Broan insert it replaced.

Who this is for

It suits a household that cooks most days at a moderate pace and cares more about a peaceful kitchen than about raw airflow. The gesture control makes it popular with families, and the slim body works in tight cabinet runs.

If you are replacing a failed over-range microwave fan on a modest gas range, it is a clean and quiet upgrade.

Where it runs out

200 CFM is the lowest airflow in this group, and it is not enough for wok cooking, cast iron searing or a wide-open burner. Know that before you buy it for a high-output gas range.

The sheet metal is thin, mounting holes are oversized enough that some owners drill their own, and the instructions only cover the ducted setup. One reviewer also reported a missing rear damper in the box.

How Much CFM Do You Actually Need for a Gas Stove?

Calculate your CFM from your burner BTU

Add up the total BTU rating printed on every burner of your gas range, then divide by 100. That gives you the minimum CFM. A 30 inch range with two 18000 BTU burners and two 10000 BTU burners totals 56000 BTU, which points to a 560 CFM minimum and a 600 CFM target.

For a light 20000 BTU gas cooktop, the same math gives 200 CFM and a 300 CFM hood. So the answer to whether 300 CFM is enough depends entirely on the burner output behind it.

Push past 600 CFM when you use a wok ring, sear on cast iron most days, or run a 48 inch range. Many installers also plan a makeup air opening at that level, which we cover below.

Duct size and static pressure decide what you really get

A hood rated at 900 CFM will not deliver 900 CFM through a long, undersized duct run. Use 6 inch round duct for 400 to 600 CFM, 8 inch round for 600 to 900 CFM, and rigid duct where you can, because flexible duct adds resistance and noise.

Count every elbow as extra length. The common rule of thumb is that a 90 degree elbow behaves like several feet of straight pipe, which is why a ducted hood straight up through a short roof penetration performs better than the same hood pushed around a corner and out a side wall.

Makeup air comes up above 600 CFM

Once a hood exceeds roughly 600 CFM, local code in many jurisdictions requires a makeup air opening, often 4 inches square or equivalent. Without it, the kitchen is under negative pressure, which pulls combustion gases back toward the range instead of drawing them out.

This is the single most common surprise on a remodel. Homeowners find out at inspection, not at purchase, and forum discussions on kitchen remodels describe the backdraft damper and makeup air trim being added late in the project.

Ducted beats ductless for gas cooking

Ductless mode recirculates air through filters and returns it to the room. That handles grease and odor reasonably well, but it does nothing for carbon monoxide or nitrogen dioxide, which are gases rather than particulates and pass straight through a charcoal filter.

For a gas stove, a ducted hood to an exterior vent is the correct choice whenever the kitchen allows it. Ductless makes sense in a condo with no vent path or a short-term rental, and it is worth accepting reduced capture performance when you make that trade.

Baffle filters beat mesh for heavy gas cooking

Baffle filters use angled baffles to knock grease out of the airstream and into a tray, and they are dishwasher-safe and permanent. Mesh filters catch grease at the surface but clog faster and need more frequent washing.

Charcoal or carbon filters are a different job. They handle odor in ductless mode and are a consumable that needs replacing, which is the cost people forget when they price a ductless setup.

Mount height matters more than people expect

Standard guidance puts the bottom of a gas range hood between 24 and 36 inches above the cooktop, with taller burners and heavier pots pushing you toward the upper end. The Broan insert in this group is specified for at least 18 inches, but that is a low ceiling, not a target.

Mount too low and the heat shortens filter life. Mount too high and capture drops because the plume has already spread. Measure from the finished cooktop surface, not the burner grates, and check that your tallest stockpot still clears.

Read the noise rating at the speed you will use

Published noise figures are almost always measured on the lowest speed with rigid ducting in ideal conditions. A rating of 50 decibels on low tells you very little about what the unit sounds like when you run it at maximum against a real 8 inch duct run.

Look for a model with more speed settings, because more speeds mean more chance of finding a quiet setting that still moves the air your burners need. The six-speed Hauslane and four-speed IKTCH models give you the most control here, and reviewers of cheaper two-speed units note they are stuck choosing between quiet and effective.

Match the hood width to the range

For gas cooking, the hood should be at least as wide as the cooktop, and wider is better. A 36 inch hood over a 36 inch range captures more of the plume than a 30 inch hood over the same range.

Height and depth matter just as much. A shallow hood over a tall pot has no capture volume above the food, and a hood set too high loses the plume before it reaches the filters.

Frequently Asked Questions

Final Verdict: Which Range Hood Wins for a Gas Stove?

For most households with a standard 30 inch gas range, the best range hoods for gas stoves come down to three picks. The Broan-NuTone 413023 insert is the editor’s choice for a reason: it carries a 4.6 average across more than twenty thousand ratings, installs in minutes, and costs you nothing in fuss. Where there is no exterior vent, that ductless design is a fair answer.

Where there is a vent, go bigger. The Hauslane PS18 at 860 CFM handles heavy gas-range cooking from inside a standard cabinet, and the IKTCH wall mount or built-in insert at 900 CFM is the answer for wok rings, cast iron and 48 inch ranges. Just remember that anything above 600 CFM needs a makeup air opening and a duct run sized to match.

Whichever route you take, match the hood width to the range, budget for a real filter cleaning routine, and check the noise figure at the speed you will actually use. If you are still working out the cookware side of things, our picks for cookware sets built for gas stoves and crepe pans for gas cooking are worth a look, and slow-cooked dishes such as our ceramic tagines for gas stoves go well with a range that is properly vented.